How to Make a Tapestry Wall Hanging | Easy Steps

0
903

Making your own wall hanging will ensure it matches your style as well as the style of your family. Wall hangings are a superb addition to any home decor. A new take on wall hangings uses the canvassed or fabric art of special choice contrary to a wooden stretcher structure. Luckily, whatever kind of wall hanging you pick to create, all of them are very easy, quick and enjoyable to complete! Keep reading to learn how to create a tapestry wall hanging.

  1. Gather all your materials.                            Source: wikiHow

The most prominent item to buy is either one canvas or else burlap measuring 2 1/2 feet by 4 1/2 feet. It is usually found at generally craft stores. You may choose any color of canvas or else burlap you like, but also remember that you will be painting designs on top of the material. Therefore, you should use lighter colors, such as white and even off-white.

  • You will also really need to grab the following accessories: painter’s tape, fabric paint, a paper tray, a smaller sized paintbrush, a guide-model with your own design of choice, sandpaper, an iron, fabric bond, two or three 7/8-inch dowels, 2 eye hooks, and then twine to place your tapestry.
  1. Lay your canvas out vertically.                                                                           Source: wikiHow                  

Determine, with a ruler, three inches from the bottom part of the canvas and then make a plain horizontal line. Take a piece of overlaying tape that is 2 1/2 feet extended then set it along this line.

  • Measure 1 inch above the masking tape, and draw another plain, horizontal line.
  • Place a 2 1/2 foot long section of masking tape along this line (edge of masking tape goes along the line).
  1. Paint your canvas.

 Source: wikiHow

Put some fabric paint on a conventional paper plate. Dip the paintbrush into the paint, and then paint between the 2 pieces of tape. However you can also slightly paint over the tape, make sure not to make loose paint on the other parts of the canvas. It is far better to dab rather than to brush in long clicks.

  • Wipe your own paintbrush off with a paper towel, after that run it under some warm water. This will get the excess paint off. Allow the paint to dry up before you correctly take out the tape strips.
  • You can also add more paint stripes above the 1 you had. Simply repeat the previous guidelines, adjusting the level of each one of your stripes (instead of a 1-inch stripe, you may want to paint a 1/2 inches stripe above the 1 you already painted).
  • Leave someplace in between both the stripe so that you can clearly see each one. Remember not to ever make too many stripes, simply because you really need some space to paint on your design. 
  1. Print out your theme.

      Source: wikiHow

You will want to stick to something basic which can be identified simply by the overview of the object or thing. Lots of simple models are available online, just like the animals, flower arrangements, architecture, etc. Whatever picture you choose, print it out, not to mention cut it out using scissors.

  • You may set the photo size when you print it out to fit your canvas. You will want it simply no higher than 2 1/2 feet in vertical length, and two feet in horizontal width.
  • When you have cut down on your own model, apply it to the canvas. Making use of a ruler to ensure that it is equidistant on the horizontal sides and vertical ends respectively.
  • Trace around the design and style with a light pencil mark, and wipe out the design.
  1. Add more texture and lifestyle to your painting.

Note: this is a strictly optional action. When your canvas is nearly dry, you can scrunch away with fabric in order to give your painting a more worn, and antiquated look. Fold it like an accordion, and immediately relieve the stress. You can also run sandpaper over the design with care. It will peel off some of the paint and make a weathered appearance.

Source: wikiHow

Source: wikiHow

  • If you choose to do this step, you will need to iron the surrounding canvas. Iron the blank canvas nearby the design, using the very low setting on the iron. Do not forget to do this on an ironing sheet.
  • Ironing the unwanted fabric will make a nice contrast in the middle of the antiquated design, and the smooth, soft canvas.
  • When you are done ironing, let your canvas rest in a secure place in order to gain wrinkle-free.
  1. Make loops at the top and bottom of your canvas.

These loops will be used to grip your dowel rods. When your design is totally dry, flip your canvas over. Take the top section of your canvas and curl it backward, so that you have 1-inch of fabric on the backside. You may crease it if you like in order to save it from constantly curling back.

  • Add some fabric gum on the border of the pulled back fabric. Do not forget to leave some space underneath for the dowel rod to slide through. Force the edge down onto the backside of your canvas and apply force until it is dry.

Source: wikiHow

  • Do the same thing at the bottom part of your canvas. Pull backward an inch of fabric and fold it over by making a crease. Add a small amount of fabric gum on the edge of the folded fabric (leaving space underneath) and then apply force until it is dry.
  • If you don’t own the patience for classic fabric gum, you may also use hot glue for a quicker drying period.
  1. Slide your dowel rods through the loops.

     Source: wikiHow

1 dowel rod for all of the 2 loops you created. Screw an eye hook onto every end of the top dowel. You should be able to screw them in by using your hand, although you may need to pre-drill a small hole so that you can help expedite the procedure.

  • Thread 1 strand of twine through both of the eye hooks. Leave some lagging twine in the middle so that you may easily hang the canvas.
    • Tie a knot on all end of the twine, close to the eye hooks. When you are done, hang your own tapestry design on the wall.